Mechanical Test of Ldpe and Hdpe P

Mechanical Test of LDPE and HDPE Processed by swelling, Injection model, Compression Molding and Sheet Extrusion Abstract LDPE and HDPE were bear upon by gibbousness, injection molding, and sheet gibbosity. Their robotlike properties such as bendable specialisation and percent elongation were measured by ductile running play and analyzed statistic all toldy (Table 2). During the exclusion process, some(prenominal) polymers underwent snuff it swelling. The water cooled polymer electric corduroys shake up a highschool tensile strength precisely impose % elongation compargond to the transport cooled corduroys. HDPE has a much high strength than LDPE delinquent to its high crystallinity.LDPE and HDPE samples processed by injection molding and sheet extrusion show the homogeneous tendency in the extent of yield strength and elastic modulus. For sheet extrusion, the take fire tempered polymer sheet has a high strength than the non-heat treated sheet because heatin g leads to an increase in both crystallinity and crystallite size. The pattern in rolled direction excessively has a high strength than those in crosswise direction collectible to the alignment of the polymer duress in rolling direction. UHMWPE (Ultra-high- molecular(a)-weight polyethylene) peach was processed by coalescency molding.The encompass particle of the saucer was examined by optical microscopy. Further, the warming temperature of PEO was determined to be 74. 0C 78. 9C. Introduction A polymer is a chemic compound or mixture of compounds consisting of geminateing structural units created through a process of polymerization. 1 The units composing polymers derive from molecules of low relative molecular mass. When all the repeating units along a chain argon of the same type, the gisting polymer is called homopolymer. Chains composed of two or more antithetic repeat units are termed copolymers.The somatic characteristics of a polymer depend both on its molec ular weight and shape, and the structure of the molecular chains. The chain structures include linear polymer, grow polymer, crosslinked polymer and network polymer. The polymer synthesized in this experiment, LDPE and HDPE, have divergent chain structures (i. e. LDPE is a ramose polymer and HDPE is a linear polymer. ). The polymer chain structure has a significant govern on polymer crystallinity, which is defined as the packing of molecular chains to do an ordered atomic array. The mechanical properties that investigated in this paper, such as tensile strength, elastic modulus and percent elongation, greatly depend on the crystallinity of the polymer sample. Polymers play an natural and ubiquitous role in everyday life from those of familiar synthetic substance plastics and other reals of day-to-day work and home life, to the natural biopolymers that are total to biological structure and function. 1 Quite a variety of different techniques are employed in the forming of poly meric materials. Molding is the most jet method for forming plastic polymers.The several molding techniques used include extrusion molding, compression molding, blow molding and injection molding. 3 During molding, crystal regions in polymer fluxs upon heating. The resulted polymer melts are non-Newtonian fluids, and their viscosity depends on the shear roam. Melt index (MI) could be used to indicate the viscosity of the fluid. It is defined as the mass of polymer satiny in ten minutes through a capillary of a specific diameter and length by a pressure applied. 4 Polymer melts are formed into a continuous charge of pasty fluid.The viscous fluid then solidifies into polymer product with specific shapes. During the solidification process, polymer melts recrystallizes and forms spherulite structure consisted of both amorphous region and lamellar. Experimental Procedure Crystallization of PEO Crystallization of PEO (Sigma-Aldrich Co. , St. Louis, MD) was spy by optical microscopy . Sample of PEO pulverise was regulated on field glass slide and heated up using hot stage. both(prenominal) the liquescent and the solidification processes were observed under optical microscope under crossed polarizer. The melting range was determined to be 74. 0C 78. 9C.Extrusion of LDPE and HDPE Both LDPE (MI = 0. 25, Equistar ) and HDPE (MI = 9, Equistar) pellets were processed into cords using single-screw extruder (Model TL3215B, Extruders ). The die temperature was 350 C, Zone temperatures were all 425 C and the screw speed was roughly 3. 6 rpm. Water cooling and style cooling were carried out for mechanical properties evaluation. malleable tests were performed on both LDPE and HDPE cords in order to evaluate their mechanical properties. Compression Molding UHMWPE (Ticona) powder was used to produce UHMWPE saucer by using a compression molding apparatus (Model 3725, Carver).The starting temperature was 245 F, and the molding temperature was 310 F. The cross section of the saucer was examined by optical microscopy. Injection Molding Both LDPE (MI = 9, Equistar) and HDPE (MI = 7, Equistar) pellets were processed into chase after bone specimens by injection molding. The barrel, nozzle and mold temperatures used are listed below. Tensile tests were performed on both LDPE and HDPE specimens in order to evaluate their mechanical properties. Table 1. Barrel, Nozzle and Mold temperatures for injection molding. LDPE HDPE Barrel Temperature 390F cdFNozzle Temperature 395F 405F Mold Temperature 275F 275F Sheet Extrusion Both LDPE (MI = 0. 25, Equistar) and HDPE (MI = 9, Equistar) pellets were processed into polymer sheets using sheet extruder (Model KLB125, Extruders). The die temperature was 375 C. Zone temperatures were all 420 C. Adapter temperature was also 420C. The screw speed was about 20 rpm and the roller speed was set up to 2. 0 rpm. Heat treatment using glass furnace was performed on both polymers. Tensile tests were carried out in order t o evaluate the mechanical properties of both LDPE and HDPE. leave behind and DiscussionCrystallization of PEO The melting temperature of PEO was determined to be 74. 0C 78. 9C, where the belles-lettres melting temperature of PEO is 65C. The polymer melting behavior is a function of the rate of heating5. That the measured melting temperature is high than the literature value results from the relative high heat rate (20C/ min). Besides, the melting temperature for polymer is a range or else of a single point. The melting temperature depends on the molecular weight of the polymer chain, the onerousness of the chain-folded lamellae, the heating rate and the impurity content.Since the PEO samples used contain polymer chains with different size, and they were heat at an inconstant rate, the melting must take place over a range of temperatures. Figure 1. Micrographs of PEO melting stage at 10X. (a). Full spherulite (red circle) growth at 54. 8C. (b). Spherulite starts to disappea r 74. 0C. (c). Spherulite exclusively disappeared at 78. 9C. A A B B C C D D Figure 2. Micrographs of PEO crystallization stages at 10X. (a). only melted polymer. (b). Spherulite start to grow from nucleation site (red circle). (c). Growing of spherulite (red circle). (d).Spherulite structure of PEO and interspherulite boundary. The spherulite consisted of chain-folded crystallites (lamellae) and amorphous region start to grow from the nucleation site at 56. 7C. individualist lamellae are separated by amorphous materials. As shown in Fig. 2 (c), the spherulite keeps growing and getting larger as the recrystallization process continues. When the crystallization of a spherulite structure nears completion, the extremities of adjacent spherulites begin to impinge on one another, forming placoid boundaries (Fig. 2 (d)). At 56. 0C, the crystallization process of PEO sample reached completion.Compression Molding A A B B Figure 3. Micrographs of middle abbreviated (B) and outer(a ) cut (A) of UHMWPE saucer at 20X. The mold is closed with a top force. Pressure is applied to force the material into contact with all mold areas, and heat and pressure are maintained until the molding material has cured. During that process, particles diffuse together and become one piece. As shown in Fig. 3, the outer cut of the UHMWPE saucer has lower porosity, and the middle section of the saucer has a much higher porosity. The outer region of the saucer was cooled much fast than the middle section of the saucer.Slowing cooling rate in the middle section led to the high porosity. Liquidus polymer shrinks as it solidify into solid leaving a large amount of pores in the middle section. Extrusion and Sheet Extrusion Die swell happened during extrusion as shown in Fig. 4. A hightail it stream has a constant rate out front entering the die. It also occupies a orbiculate conformation and maximizes the entropy. 6 As it goes through the die, polymer loses its spherical shape and be comes less entangled. Therefore, the entropy is lowered. When polymer melt comes out of the nozzle, the remaining physical entanglements cause the polymer melt to relax (i. e. egain a portion of its former shape) and concern the entropy. It appears like the polymer is swelling at the nozzle. Figure 4. Die swelling happened when polymer melt came out of the nozzle. Air cooled LDPE took 3 runs before fracture, and the water cooled LDPE took 2 runs before fracture. As shown in Fig. 5, both water cooled and air cooled LDPE cords have similar elastic modulus and yield strength. However, the air cooled cord has a higher tensile strength but lower percent elongation. Since the stratum of crystallinity depends on cooling rate during solidification, the higher the cooling rate , the higher the degree of crystallinity.Increasing in crystallinity increases the hardness but lower the ductility of the polymer cords. Thus, water cooled LDPE cord has higher tensile strength but lower % elongatio n compared to the air cooled one. Figure 5. Extrusion sample stress vs. strain plot. Red trend represents water cooled LDPE cord, and blue draw in represents air cooled LDPE cord. Figure 6. Sheet extrusion sample Stress vs. Strain plot. gruesome slue represents heat treated LDPE specimen in rolling direction. Purple curve represents non-heat treated LDPE specimen in rolling direction.Red curve represents non-heat treated LDPE specimen in transverse direction. Green curve represents heat treated LDPE specimen in transverse direction. Figure 7. Sheet extrusion sample Stress vs. Strain plot. Blue curve represents non-heat treated HDPE specimen in rolling direction. Purple curve represents heat treated HDPE specimen in rolling direction. Red curve represents non-heat treated HDPE specimen in transverse direction. Green curve represents heat treated HDPE specimen in transverse direction. Tensile test result of sheet extruded LDPE and HDPE specimens are shown in Fig. 6 and Fig. 7 abov e.HDPE specimens have higher yield strength, elastic modulus and % elongation. HDPE has a linear chain structure. It was passing packed. Therefore, it has a larger density and higher degree of crystallinity than LDPE. Molecular chains are closely packed in an ordered arrangement in perspicuous region. The alignment of the packed chains in crystalline region makes the intermolecular secondary bonding much stronger than it is in amorphous region. Thus, HDPE with higher crystallinity has a much higher strength than LDPE. The heat treated specimen has higher yield strength and tensile strength than non-heat treated specimens.It is also due to the increasing in the percent crystallinity, which makes the polymer harder but less ductile. Further, polymer specimen in rolling direction has higher yield strength and elastic modulus, but lower percent elongation compared to samples in transverse direction. It is because during outline the molecular chains slip past on another and become hig hly oriented. This alignment once again enhances the tensile modulus in the direction of drawing (RD), while reduces the tensile strength in the direction (TD) perpendicular to the rolling direction. Injection Molding Figure 8.Stress vs. Strain plot of HDPE samples processed by injection molding. Figure 9. Stress vs. Strain plot of LDPE samples processed by injection molding. Table 2. Statistic data of HDPE and LDPE samples processed by injection molding. HDPE LDPE ? y (MPa) E (GPa) %EL ? y(MPa) E (GPa) %EL 1 19. 317 0. 41 163 5. 29 0. 040 131 2 23. 216 0. 44 265 5. 38 0. 050 155 3 23. 77 0. 49 69 6. 302 0. 049 144 4 24. 142 0. 78 509 6. 408 0. 058 141 Average 22. 61 0. 53 251. 50 5. 85 0. 049 142. 75 Standard Deviation 2. 23 0. 17 189. 41 0. 59 0. 0073 9. 8 95% Confidence Interval 22. 613. 54 0. 530. 27 251. 50301. 35 5. 850. 94 0. 0490. 012 142. 7515. 72 Compared to literature value , P-value t = 3. 22,Df=3,P